The Art and Science of Wearing a Concho Belt

In Part One, All About Native American Concho Belts AKA Concha Belts, I covered a little bit about the history and makeup of a Native American concho belt.

Here I am going to talk about how to go about using that great belt you have hanging in the closet.

Men’s or Ladies?

Concho belts are unisex and can be worn with jeans as well as over shirts, blouses and with skirts and dresses.

First I’ll talk about link belts as they are quite simple.

Boulder Turquoise link belt by Platero

Link Concho Belts

Link belts are usually quite adjustable. You would purchase one approximately your waist size plus a few inches. Depending on the style of the belt, you usually can fasten the buckle’s hook on any of the rings between the conchos to get a custom fit. This is especially good if you are going to wear the belt in a variety of ways – over a blouse or shirt or through the belt loop of jeans because you will be able to fit a link belt to its intended use very quickly. Most link belts are narrow enough to fit through the loops of standard jeans. Generally 1 3/4″ wide and less will slide through belt loops.


Sterling Silver link concho belt

Depending on your waist size and the length of the link belt, you will have more or less excess belt hanging down in the front. This can be left hanging straight down or looped. 

Leather Concho Belts

Leather concho belts are traditional and popular. You need to choose a leather belt that is the correct size for the concho’s loops. If the leather strap is too narrow, the conchos will wiggle out of position. If the strap is too wide or thick, it will make it difficult to slide the conchos.

Belt is too narrow

Belt is correct width

Leather Concho belts fasten in one of three ways.

Sterling Silver link concho beltSome leather Concho Belts have a normal buckle with a tongue. With this style buckle, once you find the ideal place to punch the holes for your waist, you can cut off the end of the leather just so it tucks under the first concho as shown in the slide show below.

This slideshow requires JavaScript.

Sterling Silver link concho beltOthers leather belt style Concho Belts have a large oval or rectangular “western style belt buckle” with a prong on the back that fits into a hole in the belt. 

For both of these types of belts, using a leather punch, you will need to punch a hole or two in the leather portion of the belt to custom fit the belt to your size waist. If you have a small waist, you might want to cut some of the leather off the end of the belt and slide the conchos closer together. If you have a large waist, you might want to slide the conchos farther apart from each other.

Some leather mounted concho belts have a hook and loop on the end panels such as this one by Dan Jackson.

P1170619 use

Dan Jackson leather concho belt with hook and loop fastener

With a belt like this, you would need to slide the panels closer together or farther apart on the leather belt until the hook and loop connect perfectly for your waist size.

P1170621 use

 The leather belt portion of a leather concho belt is usually extra long and blank (not punched) so that you can custom fit the belt to your size. The conchos can be slid along the leather as desired to position them perfectly for your waist size. You can also remove the conchos and buckle from the leather strip provided and place the conchos on a favorite belt that you already own.

If you are going to wear a concho belt over an untucked shirt or blouse, you would punch a hole to fit your waist and then arrange the conchos evenly spaced around the belt.  To do this, you need two simple tools. A screwdriver and a pair of pliers.

Using the screwdriver, carefully loosen the belt loops on the back, just enough so you can slide the concho into the desired position.

Then to seat it, place a cloth around the concho to protect it and gently squeeze the belt loop with the pliers to a snug fit.

You don’t have to scrunch down real hard because the loops are usually made of copper or silver, both soft metals that bend easily. You are padding the concho so the pliers don’t make any marks on the front side of the concho – or damage any stone or inlay. Be careful when squeezing with the pliers – only enough to get the job done.  Once you have the conchos set, you are ready to wear your belt.

The situation with a belt that will be worn with jeans is a little more complicated because first you want to be sure the conchos will slip through the belt loops.

Generally 1 3/4″ wide and less will slide through belt loops.

 

P1170615 use

A few brands of jeans have larger belt loops, I have found that Seven7 Skinny Jeans accept concho belts up to 2 1/4″ wide !

 

This slideshow requires JavaScript.

Also, you will want to space the conchos so that they work in harmony with the belt loops. Here for example is one arrangement for a belt that has a buckle plus 11 conchos.

Front view

 

Back view

If you have to put your conchos and buckle on a new leather strap, simply loosen the loops and slip off the conchos. Most buckles are attached using  a 3 hole tie with lace as shown in the slide show below. It is the same tie you use to fasten a latigo to a western saddle.

This slideshow requires JavaScript.

I love to wear concho belts and hope these two articles get you motivated to use yours !

Paula

 

3 thoughts on “The Art and Science of Wearing a Concho Belt

  1. Pingback: Native American Concho Belts | Native American Jewelry Tips

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out /  Change )

Google photo

You are commenting using your Google account. Log Out /  Change )

Twitter picture

You are commenting using your Twitter account. Log Out /  Change )

Facebook photo

You are commenting using your Facebook account. Log Out /  Change )

Connecting to %s